iG330 Version History
Copyright © Speakerbus Technology Ltd. All Rights Reserved.
This document describes the features recorded for each release;
follow the links below for details on a specific release.
Back to the Home Page
Version History
Bug Fix Release
New Features Added in Version 3.400.4.0
- Add 'Delete channel' to iG330 SIP/TDM web page (SB-8148)
- Allow '+', '*' and '#' for dial strings on the iG330 SIP/TDM web page (SB-8150)
- TLS protocol used for the iG330 web pages configuration added to the iG330 'Network Settings' web page (SB-8187)
- Enforce Strict Transport Security on the iG330 web pages (SB-8192)
Defects Resolved in Version 3.400.4.0
- Web server crash (SB-8177)
- iG330 WAN monitor does not work correctly with the SIP redundancy feature (SB-8212)
- Redundancy issues with SIP TDM feature showing 'Server name resolution error' (SB-8210)
- After disabling redundancy and rebooting, the channel stats still shows the second link (SB-8213)
- After making the first ARD call, when cleared down (if you are still talking), the RX and/or TX LAN voice lamps stay lit (SB-8230)
- Minimum MRD ring settings should be removed from the SIP TDM settings (SB-8235)
Known Defects/Issues in Version 3.400.4.0
Bug Fix Release
New Features Added in Version 3.400.3.0
- Allow the use of TLSv1.3 and disable earlier versions of TLS (SB-8086)
Defects Resolved in Version 3.400.3.0
- iG330 DMVS SIP stack crash (SB-8114)
Known Defects/Issues in Version 3.400.3.0
Bug Fix Release
New Features Added in Version 3.400.2.0
- Session expiry countdown timer added to iG330 web pages (SB-7979)
Defects Resolved in Version 3.400.2.0
- The SIP TDM gateway will not correctly encrypt and decrypt RTCP packets unless the MKI length is zero or 4 (SB-7911)
- Unwanted SDP error messages in log files when encryption in use and encryption key lifetime is set (SB-7946)
- iG330 memory leak when in SIP/TDM mode that can result in the iG330 being unresponsive (SB-7934)
Known Defects/Issues in Version 3.400.2.0
Feature Release
New Features Added in Version 3.400.1.0
- Alternative SIP trunk support in TDM/SIP gateway mode (SB-7591)
Defects Resolved in Version 3.400.1.0
- Misleading TLS connection error reported on the SIP Statistics web page (SB-7478)
- The iG330 may not register to the iCS immediately after an upgrade (SB-7866)
Known Defects/Issues in Version 3.400.1.0
Bug Fix Release
New Features Added in Version 3.300.2.0
- Certificate revocation supported (SB-6739)
- Factory reset now defaults all SIP security settings and certificates (SB-6693)
Defects Resolved in Version 3.300.2.0
- Resetting multiple lines at once may cause the iG330 to reboot (SB-7477)
- Cannot perform a SFTP sendlogs, backup etc. from the iG330 webpage (SB-7684)
- The SFTP sendlogs password is not converted to **** on the iG330 web page, the password is fully visible (SB-7683)
- MRD on a SIP TDM gateway does not work after an upgrade without a reboot (SB-7682)
Known Defects/Issues in Version 3.300.2.0
Feature Release
New Features Added in Version 3.300.1.0
- Support Secure SIP (using TLS) and Secure RTP (including AES256) on the SIP trunk channels (SB-6602 & SB-6604)
- Line reference field added to iG330 channels on SIP/TDM Gateway webpage (SB-7334)
- 'De-select all' control added for channels on iG330 (SB-7311)
- Hide password when using CM SFTP commands (SB-7307)
- Store passwords in shadow file using SHA512 instead of MD5 (SB-7288)
- Block ICMP timestamp requests (SB-7404)
- Default packet size changed to 20ms for TDM SIP Gateway channels (SB-7445)
Defects Resolved in Version 3.300.1.0
Known Defects/Issues in Version 3.300.1.0
Bug Fix Release
New Features Added in Version 3.200.4.0
Defects Resolved in Version 3.200.4.0
- TDM/SIP gateway SIP messages have the wrong 'from' address (SB-7260)
Known Defects/Issues in Version 3.200.4.0
Bug Fix Release
New Features Added in Version 3.200.3.0
- Store passwords in /etc/shadow (SB-7209)
Defects Resolved in Version 3.200.3.0
- Ringback not heard on the T1/E1 side of the iG330 in SIP/TDM gateway mode (SB-7224)
- Consistency issue with menu bar background on status page (SB-7219)
- Pressing Reset Statistics on the Stats page, reloads the page twice (SB-7220)
Known Defects/Issues in Version 3.200.3.0
Bug Fix Release
New Features Added in Version 3.200.2.0
Defects Resolved in Version 3.200.2.0
- In MRD Cisco 123 ring mode, when the ring button is pressed repeatedly, the Cisco device will clear down the call and eventually reset things (SB-7090)
- Enabling Hoot Custom CAS signaling for a Hoot in SIP/TDM mode does not change the the TX CAS bits from the iG330 to the TDM line (SB-7175)
- SSH does not run after a clean install (SB-7216)
- TTL default value for unicast RTP connections is too low (SB-7136)
- When CMS service is disabled and the code is restarted, CMSIF hangs, causing the code to be repeatedly restarted (SB-7217)
Known Defects/Issues in Version 3.200.2.0
Feature Release
New Features Added in Version 3.200.1.0
- iG330 Test Tones (SB-6506)
- Add a 'Select all' control on the iG330 web pages to select all channels at once (SB-6549)
- Re-style the login web page (SB-6638)
- Re-style the tabs in the status and statistics and other web pages (SB-6637)
- Add a 'force line reset' option to the TDM/SIP web page (SB-6547)
- Remove VR mode from iG330 (SB-6941)
- Configure VLAN tagging from command line on the iG330 (SB-6943)
- Remote Syslog (SB-7020)
- Support MRD Cisco 123 ringing protocol in TDM/SIP gateway mode (SB-5514)
- Enhancements to the Cloud9 SIP trunk protocol mode (SB-7047)
- OpenSSL updated to v3.0.14
- OpenSSH updated to v9.8p1
Defects Resolved in Version 3.200.1.0
- Tab/list order of Gateway Mode is not consistent (SB-6736)
- Navigation menu shown with login page on iG330 (SB-6748)
- WAN error LED is lit when you configure the SIP / TDM feature and set call type outgoing (SB-6760)
- For SIP/TDM ARD calls, when cleared down, the RX and/or TX LAN voice LED may stay lit (SB-6769)
- Error label not consistent for iG330 Monitor in TDM/SIP gateway mode (SB-6636)
- Consistency issues with statistics of SIP trunk on iG330 webpage (SB-6797)
- iG330 TDM/SIP channel may not start when enabled (SB-6765)
- In TDM/SIP Gateway Mode, the call may be cleared down when the DMVS side is put on hold (SB-6795)
- In TDM/SIP Gateway Mode, no music on hold for an ARD call put on hold (SB-6796)
- Unable to change iG330 to use SNMP v2 after v3 has been set (SB-6920)
- Synchronising the iG330 causes it to restart and take a long time to come back into service (SB-6937)
Known Defects/Issues in Version 3.200.1.0
- In MRD Cisco 123 ring mode, when the ring button is pressed repeatedly, the Cisco device will clear down the call and eventually reset things (SB-7090)
Feature Release
New Features Added in Version 3.110.1.0
- Connection Type configuration, with options of Default and Cloud9, added to the SIP trunk configuration in TDM/SIP Gateway mode (SB-7018)
Defects Resolved in Version 3.110.1.0
Known Defects/Issues in Version 3.110.1.0
- Tab/list order of Gateway Mode is not consistent (SB-6736)
- Navigation menu shown with login page on iG330 (SB-6748)
- WAN error LED is lit when you configure the SIP / TDM feature and set call type outgoing (SB-6760)
- For SIP/TDM ARD calls, when cleared down, the RX and/or TX LAN voice LED may stay lit (SB-6769)
- Error label not consistent for iG330 Monitor in TDM/SIP gateway mode (SB-6636)
- Consistency issues with statistics of SIP trunk on iG330 webpage (SB-6797)
- iG330 TDM/SIP channel may not start when enabled (SB-6765)
- In TDM/SIP Gateway Mode, the call may be cleared down when the DMVS side is put on hold (SB-6795)
- In TDM/SIP Gateway Mode, no music on hold for an ARD call put on hold (SB-6796)
- Unable to change iG330 to use SNMP v2 after v3 has been set (SB-6920)
- Synchronising the iG330 causes it to restart and take a long time to come back into service (SB-6937)
Bug Fix Release
New Features Added in Version 3.100.3.0
Defects Resolved in Version 3.100.3.0
- TDM/SIP ARD calls connected from the TDM side fail to connect after the first successful call (SB-6717)
- iG3xx Production Test failure (SB-6710)
Known Defects/Issues in Version 3.100.3.0
Bug Fix Release
New Features Added in Version 3.100.2.0
- Add setting on the TDM SIP Gateway web page to configure the listening port for the SIP Signalling (SB-6520)
- Enhancements to the iG330 Monitor tool to include SIP trunk channels when in TDM/SIP Gateway mode (SB-6519)
- Add a refresh link to the status and statistics pages (SB-6542)
Defects Resolved in Version 3.100.2.0
- Calls not establishing after a failed state in TDM/SIP gateway mode (SB-6476)
- Disabling SIP UDP in TDM/SIP gateway mode does not disable UDP signalings (SB-6517)
- TCP SIP Protocol will always use port 5060 in TDM/SIP gateway mode (SB-6477)
- G.723 should not be an available codec option in TDM/SIP gateway mode (SB-6479, SB-6481, SB-6510)
- Unable to set a packet size of 60ms in TDM/SIP gateway mode (SB-6483)
- Packet size does not change for outgoing iG330 SIP calls in TDM/SIP gateway mode (SB-6484)
- In TDM/SIP Gateway mode the Engineering Tools->Status page shows the iCS Status as "Enabled" when it should be shown as "Disabled" (SB-6526)
- In Web Page Control mode, the Status web page can show the iCMS status as Out-Of-Sync (SB-6527)
- The Status->SIP Trunk "MRD call signalling capability" on the outgoing gateway shows unknown (SB-6507)
- The iG330 can accept multiple calls into a voice service in TDM/SIP gateway mode (SB-6513)
- It should not be possible to enable VAD when using G.722 as this is not supported (SB-6485)
- An "Unexpected status code 200" message is logged every time a SIP Re-INVITE is sent (SB-6572)
- Navigating to a different page on the iG330 does not restart the inactivity timeout period (SB-6628)
- When using Chrome, closing the browser tab does not log out the user (SB-6626)
- iG330 webpages sometimes does not load correctly (SB-6569)
- 'Reset Statistics' on Engineering Tools->Statistics->SIP Trunk page does not work (SB-6642)
Known Defects/Issues in Version 3.100.2.0
Feature Release
New Features Added in Version 3.100.1.0
- TDM/SIP Gateway mode added (SB-5495)
- VLAN tagging support added (SB-6240)
- Enhanced navigation panel on web pages (SB-6311)
- OpenSSL updated to v3.0.12
- OpenSSH updated to v9.6p1
- JQuery updated to v3.7.1
- Remove deprecated SHA1 settings for SSH (SB-6291)
- Increase iG330 webpage inactivity time out to 30 minutes (SB-6341)
Defects Resolved in Version 3.100.1.0
- Virtual address goes offline after a failover and the primary is brought back online (SB-3938)
- CM defaultfactory does not delete Root or SBEngineer history files (SB-6273)
- iG33x board can reset when doing a full installation via u-boot (SB-6287)
Known Defects/Issues in Version 3.100.1.0
Bug Fix Release
New Features Added in Version 3.000.2.0
Defects Resolved in Version 3.000.2.0
- Unexpected behaviour when logged into the iG330 webpage with the Mozilla Firefox Browser (SB-4560)
- SIP error when configured for IPv6 with TCP transport (SB-4584)
- No audio is being transmitted to the far end iG330 Gateway when 'Voice Recording Mode' is enabled (SB-4583)
- iG330 sending out DNS queries when it should not be doing so (SB-4627)
Known Defects/Issues in Version 3.000.2.0
Feature Release
New Features Added in Version 3.000.1.0
- Add SFTP support as an alternative to TFTP
- iG330 factory default supported (SB-4022)
- Change 'System Default' in the Engineering Tools->Maintenance web page to 'Factory Default' (SB-4185)
- Remove 'Disabled' as an 'IP mode' option on the iG330 Network Settings web page (SB-4160)
- Treat any multicast address as an invalid 'IPv4 address' or 'IPv6 address' on the iG330 Network Settings web page (SB-4161)
- Remove 'A note about your browser' section from the iG330 welcome web page (SB-4183)
- Limit the number of characters for the password on the iG330 webpage login (SB-4205)
- Upgrade JQuery on the iG330 to v3.6.1 (SB-4225)
- Do not report MCC 'Not Connected' as an error, when no multicast MCC messages are received (SB-4270)
- Update SSL cipher suite for the internal web server (SB-3530)
- Update openSSL (to 1.1.1q) and openSSH (to 9.0p1) (SB-4288)
- Set a Content-Type header value for all the web pages on the iG330 (SB-4302)
- Lock user out of iG330 web page after too many unsuccessful login attempts (SB-4304)
- World-writable files removed from the iG330 (SB-4316)
- Updated WAN monitor tool
Defects Resolved in Version 3.000.1.0
- IP_ENABLE messages from iCMS via name do not work (SB-3045)
- The IPv4 and IPv6 addresses cannot be set in the RTP Settings web page (SB-3228)
- Handle ICS IPv4 & IPv6 CMS element names correctly in iG330 (SB-2267)
- If the 'CM backup' command fails, it still reports 'Backup completed successfully' (SB-4177)
- A properly configured iG330 shows the iCS address & port as 'none' in red on the web page when offline (SB-3533)
- The IPv6 alias address (virtual address used for redundancy) is not removed from the network interface when the redundancy state switched to Offline (SB-1027)
- Issues seen when using Chrome to access the iG330 web pages (SB-4247)
- Possible MTFIF crash in the iD808 (SB-4243)
- iG330 Linux Security Vulnerabilities (SB-4276)
- When making, clearing down and answering DMVS calls, log messages are generated on the iG330 (SB-4322)
- When upgrading an iG330, under web-page control, from 2.760 to 2.802.1.0 some settings are lost (SB-4375)
- Cannot access iG330 webpage using its IPv6 address (SB-4394)
- The iG330 is listening on more SIP ports than required (SB-4455)
- Improvements to the operation of the dhcpcd client (SB-4427)
- Setting a voice recorder on the iG330 webpage renders the gateway unusable (SB-4282)
Known Defects/Issues in Version 3.000.1.0
Bug Fix Release
New Features Added in Version 2.802.1.0
- Added IPv6 support to tftp command.
Defects Resolved in Version 2.802.1.0
- Gateway stops re-registering with iCS once the iCS went for restart/fail-over/unreachable.(F0038937, F00038961)
- Reading some specific OIDs using an SNMP-GET, can cause the iG330 to run out of memory and stop working (F0038945)
- Password expiry check box ticking itself after deleting a voice service channel and syncing from iManager (F0038971)
Known Defects/Issues in Version 2.802.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
- Removal of error message (F0038754)
- Incorrect name for iG330 devices on CMS (F0038733)
Bug Fix Release
New Features Added in Version 2.801.3.0
- Improve downgrading of dual stack code to single stack code, maintaining key network and iCMS configuration.
Defects Resolved in Version 2.801.3.0
- Spelling mistakes on the "Before You Begin" web page(F0038735)
- Missing space in 'Backup and Restore' page (F0038862)
- Primary iG330 not coming back as 'Online' after a failover has occurred (F0038880)
- Virtual address goes offline after a failover and the primary is brought back online (F0038881)
- Various mistakes in the release documentation (F0038883)
- ::ffff: included in 'Last contacted iCMS server' (F0038892)
- Update iG330 webpage to include the new Speakerbus logo (F0038893)
- Update release documentation to include the new Speakerbus logo (F0038908)
- Broken links in the release documentation (F0038909)
- The working iCMS IP address is not cleared when the setting from iCMS is cleared (SB-1551)
Known Defects/Issues in Version 2.801.3.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
- Removal of error message (F0038754)
- Incorrect name for iG330 devices on CMS (F0038733)
Bug Fix Release
New Features Added in Version 2.801.2.0
- Improved M_INFO reporting for CheckProfile responses to iCMS.
Defects Resolved in Version 2.801.2.0
- iG330 not accepting live profile update from CMS when changing RTP connection address (F0038787)
- Fix display during upgrade using CM command so as not to show a 'deprecated key derivation' warning (F0038852)
- Virtual IP address going offline when primary iG330 is powered off or loses network connection (F0038847)
- Secondary iG330 not becoming active after a failover has occurred (F0038848)
- The Time Zone is not updated via iCMS on iG330 gateways.
Known Defects/Issues in Version 2.801.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
- Spelling mistakes (F0038735)
- Removal of error message (F0038754)
- Incorrect name for iG330 devices on CMS (F0038733)
- Missing space in 'Backup and Restore' page (F0038862)
Minor Release
New Features Added in Version 2.801.1.0
- Upgraded OpenSSL to 1.1.1k
- Upgraded OpenSSH to openssh-8.5p1
- Support added for generating test tones for regression testing
Defects Resolved in Version 2.801.1.0
- Fix where, during iCS failover, gateway registrations are failing when SIP signalling is over TCP
- Virtual IP address for resilience does not work (F0038811)
- Minor spelling mistake on the Network status web page (F0038812)
- Fix for potentially accessing the BinaryData arrays out of range
- Fixed snmpd error messages after an upgrade
- IPv6 fixes
Known Defects/Issues in Version 2.801.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
- Spelling mistakes (F0038735)
- Removal of error message (F0038754)
- iG330 not accepting live profile update from CMS when chaing RTP connection address (F0038787)
- Incorrect name for iG330 devices on CMS (F0038733)
Bug fix release.
New Features Added in Version 2.800.3.0
- Kernel updated to implement RFC5961 (Send a challenge ACK if receive ACK or RST in TCP window, but not with next sequence number). This resolves Qualys QID 82054
Defects Resolved in Version 2.800.3.0
- After doing an upgrade of the firmware from v2.760 to v2.800.2.0, the gateways are no longer reachable. (F0038676)
- After doing an upgrade of the firmware from v2.760.1.0 to v2.800.2.0 the gateways have lost connection with the iCMS. (F0038691)
- When downgrading the IG330 from 2.8 to 2.7, the gateway becomes unresponsive in iManager. (F0038713)
- When changing the iG330 to web page mode, the pop-up box asking the user to reset the device says 'Goto' instead of 'Go to'. (F0038707)
- "Log Out" button does not work on the Network settings page. (F0038709)
- Running the "CM restart" command does not execute correctly and results in the script being aborted (after "CM defaultall" has been run). (F0038711)
- Unable to reset web UI password of IG330 on version 2.800.2. (F0038714)
Known Defects/Issues in Version 2.800.3.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
Feature Release.
New Features Added in Version 2.800.2.0
- SNMP V3 configuration supported.
- Maximum number of SNMP managers configurable increased from 10 to 20.
- SNMP MIB-II SysObjectID set to the iG330 MIB OID.
- Change SNMP passwords and community strings to type 'password' instead of 'text' on the web page.
Defects Resolved in Version 2.800.2.0
- TFTP port fixes.
- Fix issue where iD704 DMVS ARD call did not ring on the far site.
- IPv4 addresses for the SNMP managers cannot be configured from the web page.
- IPv6 bug fixes.
- Certificates are unable to use the configurable TFTP port function. (F0038629)
Known Defects/Issues in Version 2.800.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
Feature Release.
New Features Added in Version 2.800.1.0
- Dual IP stack (IPv6 ready)
Defects Resolved in Version 2.800.1.0
- MCC not working - the Linux code receives no MCC packets though they are received by the DSPCode. (F0038517)
Known Defects/Issues in Version 2.800.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
Bug fix release.
New Features Added in Version 2.760.1.0
- Support added for individual SNMP traps.
Defects Resolved in Version 2.760.1.0
Known Defects/Issues in Version 2.760.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
Bug fix release.
New Features Added in Version 2.750.1.0
- TFTP port configurable.
- DSCP value for SIP messages configurable .
- Change the NTP configuration to set the maximum synchronisation distance.
Defects Resolved in Version 2.750.1.0
Known Defects/Issues in Version 2.750.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- When failover was activated onto a standby iG330 the web page display intermittently reported the MCC as down. (F0038065)
Bug fix release.
New Features Added in Version 2.740.2.0
Defects Resolved in Version 2.740.2.0
- Cannot configure HOOT_CUSTOM_CAS from iCMS or the web interface. (F0038046)
- Minor changes/corrections to the wording of some SNMP traps.
Known Defects/Issues in Version 2.740.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
'Custom Hoot' feature added.
New Features Added in Version 2.740.1.0
- Added new 'Custom Hoot' mode to allow the Tx CAS pattern on all active hoot mixer groups to be configured.
- Various security updates:
- Updated OpenSSL to version 1.1.1b (released 26/2/19) from version 1.0.2j.
- Updated OpenSSH to version 8.0p1 (released 17/4/19) from version 7.3p1.
- Updated iG3xx web server to work with OpenSSH to version 8.0p1
- Updated Net-SNMP to work with OpenSSH to version 8.0p1
- Updated iG330Monitor to work with OpenSSH to version 8.0p1
- Removed support for TLS 1.0 and 1.1.
- Removed support for the unencrypted upgrader process.
Defects Resolved in Version 2.740.1.0
- Ethernet port 2 on iG330 or iG334 with the latest software does not pass any packets when it is enabled. (F0036606)
Known Defects/Issues in Version 2.740.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
SNMP feature release, bug fix update.
New Features Added in Version 2.731.1.0
Defects Resolved in Version 2.731.1.0
- The iG330 shows the wrong Variable Binding for an iG330-alert-unit when both the SIP registration and MCC are down. It should show both the SIP registration and MCC are down and none for the clear. (F0037165)
Known Defects/Issues in Version 2.731.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- Ethernet port 2 on iG330 or iG334 with the latest software does not pass any packets when it is enabled. (F0036606)
SNMP feature release, bug fix update.
New Features Added in Version 2.730.4.0
Defects Resolved in Version 2.730.4.0
- The iG330 SNMP traps include null strings if there is nothing to report. These should be a single dash. (F0036985)
Known Defects/Issues in Version 2.730.4.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- Ethernet port 2 on iG330 or iG334 with the latest software does not pass any packets when it is enabled. (F0036606)
SNMP feature release, bug fix update.
New Features Added in Version 2.730.3.0
Defects Resolved in Version 2.730.3.0
- Correction to include script files missing from previous release.
Known Defects/Issues in Version 2.730.3.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
SNMP feature release.
New Features Added in Version 2.730.2.0
- SNMP traps enhanced to have a single trap per status type and to improve the variable bindings associated with the traps.
Defects Resolved in Version 2.730.2.0
Known Defects/Issues in Version 2.730.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
SNMP feature release.
New Features Added in Version 2.730.1.0
- SNMP enhanced to use Speakerbus OIDs and to add more details to the traps.
- The web pages enhanced to auto logout the user when the browser window is closed.
Defects Resolved in Version 2.730.1.0
- CM start_prodtest command fails to complete. (F0036220)
Known Defects/Issues in Version 2.730.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
Bug fix release.
New Features Added in Version 2.720.3.0
- Additional HTTP response headers to improve the security of the iG330 webpages.
- Prevent SSH from using CBC mode. (Feature Request 2246)
Defects Resolved in Version 2.720.3.0
- No pause between re-registration attempts when iCS is not contactable. (F0036159)
Known Defects/Issues in Version 2.720.3.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
Bug fix release.
New Features Added in Version 2.720.2.0
Defects Resolved in Version 2.720.2.0
- The DSP status log is not included in the TechSupport logs when initiated from iManager. (F0036122)
Known Defects/Issues in Version 2.720.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
Minor feature release.
New Features Added in Version 2.720.1.0
- Configuration of the 'SbRTP lost' timeout.
- Support for configuration of various SIP registration timers.
Defects Resolved in Version 2.720.1.0
- showCAS 10 does not display the CAS signalling for this channel, other channels show the correct values. (F0035869)
- Filesystem can fill with log files causing software upgrades to fail. (F0036037)
Known Defects/Issues in Version 2.720.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
Minor feature release.
New Features Added in Version 2.710.1.0
- UDP/TCP SIP Signalling configuration
- UDP SIP Signalling can be disabled
Defects Resolved in Version 2.710.1.0
- Fix potential issue in generating SIP subscription messages, to match iD712, SE708 & iD808. (F0035836).
Known Defects/Issues in Version 2.710.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
- showCAS 10 does not display the CAS signalling for this channel, other channels show the correct values. (F0035869)
Bug fix release.
New Features Added in Version 2.702.1.0
- Remove security vulnerability CVE-2002-0510.
- Various DSP improvements to reduce the possibility of network FIFO errors.
Defects Resolved in Version 2.702.1.0
Known Defects/Issues in Version 2.702.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
Bug fix release.
New Features Added in Version 2.701.1.0
Defects Resolved in Version 2.701.1.0
- One way voice when using DMVS ARD when a secondary IP address is assigned to the iG330. (F0035600)
Known Defects/Issues in Version 2.701.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
New Features Added in Version 2.700.3.0
- Speakerbus enterprise MIB supported.
- Number of SNMP managers supported increased to 10.
Defects Resolved in Version 2.700.3.0
- The iG330 mixer group may be mismatched if a Dynamic DMVS and static mixer group have the same ID. (F0035008)
Known Defects/Issues in Version 2.700.3.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
New Features Added in Version 2.700.2.0
Defects Resolved in Version 2.700.2.0
- IGMP messages use an incorrect source IP address (previous fix included in v2.700.1.0 was found to be incomplete). (F0033239)
Known Defects/Issues in Version 2.700.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
-
The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
See 2.610.1.0 Security Enhancements for details.
New Features Added in Version 2.700.1.0
- Added support for DMVS Intercom & Group calls.
- Added diagnostic code to report on received bad CAS signalling.
- Added additional receive CAS operating modes to improve operation with signalling glitches.
- Added framework necessary for the secure upgrade process, this will be enforced in the next major formal release. (Feature Request 281)
- Added a SSH command to enable network trace (CM networktrace [on|off]). (Feature Request 1718)
- Added webpage support to allow SSH to still be enabled if iCMS has locked this interface. (Feature Request 1994)
- Added support to the web page interface to allow the setting of RTCP DSCP values. (Fragment 70)
- Added basic dialog box to confirm when an upgrade has been initiated from the webpage. (Fragment 88)
- Update OpenSSL and OpenSSH packages to the latest appropriate version to improve security.
- Allow custom items to be added to the techsupport tar file via the SBEngineer/techsupport directory.
Defects Resolved in Version 2.700.1.0
- IGMP messages use an incorrect source IP address. (F0033239)
- ARD calls that are not fully cleared from both ends can result in a new call not fully connecting, resulting in one-way audio. (F0034150)
- Miscellaneous enhancements to CAS operation to improve call-collision behaviour.
- Various fixes to CAS signalling stack to improve reliability.
Known Defects/Issues in Version 2.700.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
- The enhanced internal self-signed certificate added in 2.610.1.0 is overwritten when upgrading from earlier versions. (F0033096)
New Features Added in Version 2.610.2.0
Defects Resolved in Version 2.610.2.0
- The OpenSSL library updated in 2.610.1.0 prevents the SNMP process from starting. (F0032760)
- Potential process hang when exiting (defect common to other products), in reality this is unlikely to affect iG330. (F0032694)
Known Defects/Issues in Version 2.610.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
New Features Added in Version 2.610.1.0
- Security Enhancements:
-
Update internal self-signed certificate to improve security (2048-bit RSA encryption, SHA256 signed).
-This new certificate will only be used once the command 'CM certdefault' is executed following an upgrade (not needed for a full install).
-
Update OpenSSL and OpenSSH packages to the latest version to improve security.
-From this version onwards it will be necessary to use the updated WAN-monitor tool to work with the stricter SSH security requirements.
- Insert X-Frame-Option 'SAMEORIGIN' into appropriate frames to improve click-jacking resistance: NPD Fragment 156.
- Prevent web page auto-complete of sensitive fields: NPD Fragment 157.
- Reduced device start-up time by using the faster DSP loading methods used in other products.
Defects Resolved in Version 2.610.1.0
- TDM line interface reconfiguration can trigger TDM sync issue detection. (F0031910)
- Potential memory leak in iD808 derived SIP stack, in reality this should never affect iG330. (F0031355)
Known Defects/Issues in Version 2.610.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
New Features Added in Version 2.601.3.0
- When a web interface login is rejected because another user is already logged on, display the logged in users IP address.
- Do not display the DSP loading line on iG330s under iCMS control. (Feature Requests 1719 and 1784).
- Add RX packet sizes to the web pages for each source (Fragment 1584).
Defects Resolved in Version 2.601.3.0
- iG330 can power up with statically configured WAN links not transmitting any traffic. (F0031880)
- Do not show voice activity in WAN Monitor or LEDs for listen only SbRTP voice services. (F0030985)
- Minor corrections:
- Re-mute a previously muted T1/E1 channel when removing the diagnostic handset from that mixer group.
- Fix colour scheme differences between web pages.
Known Defects/Issues in Version 2.601.3.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
- Potential memory leak in iD808 derived SIP stack, in reality this should never affect iG330. (F0031355)
New Features Added in Version 2.601.2.0
Defects Resolved in Version 2.601.2.0
- The Static WAN Status isn't populating when viewed with Firefox. (F0031843)
- Changed description of new sync counter in TDM status web page to 'TDM sync issue count'.
Known Defects/Issues in Version 2.601.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
- WAN monitor can still show notional Tx SbRTP Voice activity when the link is configured as 'listen only'. (F0030985)
- Potential memory leak in iD808 derived SIP stack, in reality this should never affect iG330. (F0031355)
New Features Added in Version 2.601.1.0
Defects Resolved in Version 2.601.1.0
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-Code. (F0031755/F0022929/F0027011)
Known Defects/Issues in Version 2.601.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
- WAN monitor can still show notional Tx SbRTP Voice activity when the link is configured as 'listen only'. (F0030985)
- Potential memory leak in iD808 derived SIP stack, in reality this should never affect iG330. (F0031355)
New Features Added in Version 2.600.1.0
- SNMP enhancements to match iD808, with additional status variables and traps.
- Configurable Ethernet MTU.
- Web page styling refreshed to better match other products.
- Default RTP port range updated to better match other products (NPD Fragment 61 and also resolves F0030157).
Defects Resolved in Version 2.600.1.0
- DMVS & static IP WAN RTP default port number clash. (F0030157)
- New Spansion NAND flash incorrectly reported in kernel; U-boot change still pending, see below. (F0026510)
Known Defects/Issues in Version 2.600.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported in U-boot. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
New Features Added in Version 2.500.7.0
Defects Resolved in Version 2.500.7.0
- Privacy cannot be established for a local MRD DMVS talker when using SbRTP in a static MRD setup (DMVS+SbRTP) when there is a local listener. (F0029727)
- CVE-2015-0235 "GHOST" vulnerability in C library. (F0029955)
- Specific IGMP membership query messages are not handled resulting in multicast not being received until the next general IGMP membership query. (F0029986)
- Actions taken to mitigate detected network audio loops can result in stuck voice services. (F0030011)
- Delay before a new voice service is registered with iCS. (F0030034)
Known Defects/Issues in Version 2.500.7.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
New Features Added in Version 2.500.6.0
- Changed some heading names in new 'General' status page tab.
Defects Resolved in Version 2.500.6.0
- Loss of SIP re-invites for individual DMVS connections may be missed, leaving failed connections active. (F0029591)
- Possible crash if the device is repowered when creating configuration files. (F0029615)
- 'Apply' on the Voice Services web page for any mixer group can unintentionally remove the handset attached to a different mixer group. (F0029633)
- Invalid Security Certificate filename accepted on the 'install certificate' web page. (F0029458)
- Some SIP registration rejections from iCS may not be immediately handled, causing a delay in any response action. (F0029653)
- The prime user bit may oscillate during silence periods for VAD DMVS calls using global muting. (F0029620)
- Rapidly toggling talk on Hoot/MRD DMVS calls can eventually cause the gateway to drop the call. (F0029683)
Known Defects/Issues in Version 2.500.6.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
New Features Added in Version 2.500.5.0
- Addition of new 'General' and 'TDM' status page tabs to provide information on the current overall unit and TDM interface status.
Defects Resolved in Version 2.500.5.0
Known Defects/Issues in Version 2.500.5.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
New Features Added in Version 2.500.4.0
- Force iG330 SIP re-registration every 30 secs when the SIP session for any MRD or Hoot channel is not established. (F0029441)
- Upgrader tar file can be stored in the TFTP server�s root directory as an alternative to its upgraders/ directory (from v2.x only).
- Minor time zone corrections/updates.
Defects Resolved in Version 2.500.4.0
- Call collisions for simultaneous outgoing and incoming DMVS calls can leave the call not properly connected. (F0029302)
- Global muting signalling changes may not be propagated correctly for DMVS WAN streams with VAD enabled (Requires matching iD808 & iCS changes). (F0029293)
- DSP loading calculation on web page differs from iCMS due to rounding differences. (F0029384)
- iG330 does not always fully clear DMVS calls if communication with iCS is lost. (F0029416)
- iG330 does not unregister a previous SIP registration when iG330 is stopped or restarted. (F0029443)
- WAN errors not reported for ARP failures for gateway/router. (F0029427)
- Invalid Security Certificate can prevent subsequent web interface access. (F0029458)
- iG330 does not reject unsupported media requests from iCS. (F0029485)
Known Defects/Issues in Version 2.500.4.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
New Features Added in Version 2.500.3.0
- Configuration setting added to specify the presumed DMVS SbRTP packet size for the DSP loading calculation.
- Minor enhancements to WAN link status & statistics web pages error reporting.
Defects Resolved in Version 2.500.3.0
- Occasional Tx RTCP packet corruption, which can cause WAN stream signalling issues. (F0029188)
- Changes to the RTP preferred codec setting are not handled correctly, resulting in the wrong preferred codec being used. (F0029290)
Known Defects/Issues in Version 2.500.3.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
- Global muting signalling changes may not be propagated correctly for DMVS WAN streams with VAD enabled. (F0029293)
- Call collisions for simultaneous outgoing and incoming DMVS calls can leave the call not properly connected. (F0029302)
New Features Added in Version 2.500.2.0
- Addtional web page status & statistics information added for DMVS links.
Defects Resolved in Version 2.500.2.0
- A link can occasionally think there is no Rx RTCP signalling, causing calls to be dropped. (F0028932)
- If a WAN link error occurs then the previous, now stale, signalling continues to be used. (F0029078)
- Occasional failure of the SIP stack to initialise due to a DNS interface initialisation error. (F0029079)
- The DSP can sometimes fail to pass on SbRTP signalling changes when an endpoint enters/exits its internal 'holding' state. (F0029087)
- DSP can continue to generate Prime User signalling after the originating stream has ended. (F0029122)
- Temporary �extra-sources� WAN stream error reported sometimes when iCS changes DMVS RTP streams. (F0029171)
- Improved accuracy of SbRTP/WAN statistics 'late packet' reporting.
- Improved handling of incorrect/unexpected iCS events.
Known Defects/Issues in Version 2.500.2.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- First received audio packet after a link is created is not decoded. (F0029123)
- Audio artifacts can be heard during quiet speech when using G723 with VAD enabled. (F0029150)
New Features Added in Version 2.500.1.0
- Add support for DMVS Hoot & Private wire connections (configurable via iCMS only).
- Add support for diagnostic handset with Voice Recorder & DMVS streams.
- Enhance web page status & statistics.
- Add support for Network, iCMS & iCS status information with Autodiscovery.
- Enhance 'Ready LED' to indicate additional critical configuration errors.
- Enhance WAN monitor to show DMVS RTP & SbRTP activity and a summary of the basic Network, iCMS & iCS status information.
- Add support for G.723 audio codecs.
- Improve performance of G.729 & G.722 audio codecs.
Defects Resolved in Version 2.500.1.0
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- Unpredictable operation caused by multiple coincident restarts. (F0027134)
- 'No Rx RTCP' WAN error reported unexpectedly. (F0026933)
- WAN Statistics 'Remote Lost Packets' count may be wrong (F0027945).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383, F0027522)
- Voice Service web page not correctly displayed with IE8. (F0028755)
- String parameters from iCMS containing an escaped ampersand character are not un-escaped. (F0028790)
- Initialisation issues when DHCP server timeout is set to 1 second. (F0028851)
- Login web page can cycle endlessly in Internet Explorer. (F0028980)
- Recorded against unreleased code:
- SbRTP/RTP signalling events missed (F0027943).
- G.723 audio & signalling issues (F0027944).
- IGMP join request made for default MCC address when this is not required (F0028681).
- IGMP join fails if attempted for more than 20 SbRTP links simultaneously (F0028839).
- Asymmetric audio codec operation not supported for non G.711 codecs. (F0028838).
Known Defects/Issues in Version 2.500.1.0
- The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will not operate in the same manner as an IP WAN mesh.
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
New Features Added in Version 2.100.4.0
Defects Resolved in Version 2.100.4.0
- Disabling E1 CRC4 framing may not work correctly without a restart. (F0028443)
Known Defects/Issues in Version 2.100.4.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383, F0027522)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- Unpredictable operation caused by multiple coincident restarts. (F0027134)
- 'No Rx RTCP' WAN error reported unexpectedly. (F0026933)
New Features Added in Version 2.100.3.0
- Changes to Production Tests commands.
- Change to root password.
- Change web page statistics sample period to 10 seconds to allow more meaningful counts to be presented.
Defects Resolved in Version 2.100.3.0
- Guest cannot change Guest password. (F0027694)
- Miscellaneous improvements to web page handling of special characters.
- LAN status web page always reports 'Tx audio source ID' as 0. (F0017227)
- WAN Statistics 'Remote Lost Packets' count may be wrong. (F0027945)
- Shared WAN IP address with 12 dotted-decimal digits does not work. (F0028168)
- 'Destination Unreachable' error reported if the Gateway Router is unconfigured. (F0028243)
Known Defects/Issues in Version 2.100.3.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383, F0027522)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- Unpredictable operation caused by multiple coincident restarts. (F0027134)
- 'No Rx RTCP' WAN error reported unexpectedly. (F0026933)
This is an initial release of v2.1 code intended solely for use in Approvals testing.
New Features Added in Version 2.100.2.0
Defects Resolved in Version 2.100.2.0
- Once triggered, the E1 distant multiframe alarm indication (if enabled) remains set even after the alarm condition has cleared. (F0027820)
Known Defects/Issues in Version 2.100.2.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- Unpredictable operation caused by multiple coincident restarts. (F0027134)
- 'No Rx RTCP' WAN error reported unexpectedly. (F0026933)
This is an initial release of v2.1 code intended solely for use in Approvals testing.
New Features Added in Version 2.100.1.0
- Replace E1 Automatic Interworking mode with always-on mode.
- Feature Request 1568 added (Turn off LOS/F LED when no TDM is in use).
Defects Resolved in Version 2.100.1.0
- Audio lost in both directions following a configuration change. (F0027516)
Known Defects/Issues in Version 2.100.1.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- Unpredictable operation caused by multiple coincident restarts. (F0027134)
- 'No Rx RTCP' WAN error reported unexpectedly. (F0026933)
New Features Added in Version 2.000.5.0
Defects Resolved in Version 2.000.5.0
- Changing the Secondary IP address (used for Failover) can occasionally cause phantom Rx signals on a pre-existing SbRTP link. (F0027398)
- A call can end up stuck with one way audio. (F0027463)
- An SNMP IP address greater than 11 characters is truncated. (F0027472)
Known Defects/Issues in Version 2.000.5.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- Unpredictable operation caused by multiple coincident restarts. (F0027134)
- 'No Rx RTCP' WAN error reported unexpectedly. (F0026933)
New Features Added in Version 2.000.4.0
Defects Resolved in Version 2.000.4.0
- Unit can get 'stuck' offline when Ethernet link is disrupted after failover operation is disabled. (F0027305)
- Cannot assign a blank IP address to the DNS servers from the network settings webpage. (F0019702)
- 'No Rx RTCP' WAN error reported unexpectedly. (F0026933)
Known Defects/Issues in Version 2.000.4.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- Unpredictable operation caused by multiple coincident restarts. (F0027134)
- Changing the Secondary IP address (used for Failover) can occasionally cause phantom Rx signals on a pre-existing SbRTP link. (F0027398)
New Features Added in Version 2.000.3.0
- SbRTP TTL default value changed from 1 to 2 (NPD Fragment 122).
Defects Resolved in Version 2.000.3.0
- Web page tab can show incorrect device name of iG3330_000000. (F0026770)
- iG330 stops responding to iCMS commands. (F0026948)
- Digital Line audio codec change not applied (via restart). (F0026991)
- NTP & DNS web page settings tooltips do not explain the need to refresh the page to see the change. (F0027013)
Known Defects/Issues in Version 2.000.3.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
- 'No Rx RTCP' WAN error reported unexpectedly. (F0026933)
- T1/E1 timeslot audio can very rarely be shifted to an adjacent timeslot and then masked by the Idle-code (F0022929/F0027011)
- Inconsistent treatment of web page user data entry errors. (F0027014)
- Unpredictable operation caused by multiple coincident restarts. (F0027134)
New Features Added in Version 2.000.2.0
Defects Resolved in Version 2.000.2.0
- Specific network disruption failover modes can leave remote iG330 indicating WAN errors until there is a signalling event. (F0026671)
Known Defects/Issues in Version 2.000.2.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
New Features Added in Version 2.000.1.0
- Full support for configuration via iCMS.
- Automatic iCMS location via DHCP.
- Automatic active/standby failover operation.
- Configurable digital line voice-switching on a per channel basis.
- Web page configuration of iCMS server, Failover, SNMP and voice-switching.
- Web page interface can be locked to prevent conflict with iCMS.
- Engineer and Admin login credentials updated to match current product range.
- SSH now enabled by default as not configurable from iCMS.
- Support for secondary NTP & DNS servers.
- Minor miscellaneous web page improvements.
Defects Resolved in Version 2.000.1.0
-
IP WAN links that are connected to a mixer group and then updated with an IP address of 0.0.0.0 are still
shown attached to the mixer group and cannot be deselected (F0015529).
-
It is possible to have greyed out ticks against SbRTP links and T1/E1 channels for a mixer group
on the Voice Service web page that are not assigned to any group (F0017623).
- The .sh upgrader file has to be placed in the root directory of the TFTP server. (F0017793 / FR 627)
- TDM Ring Indication tones volume could not be 0. (F0023137)
- Web page LAN & WAN status are not cleared when the device is taken offline or stops receiving packets from the remote site. (F0025520)
- Manual failover did not recover. (F0025541)
- WAN link audio transmit using G722 and G729 gives continuous noise. (F0026188)
- Single digit IP addresses from iCMS converted to 0. (F0026403)
- Browser edit boxes incorrectly formatted for IP addresses at some zoom settings. (F0026428)
- Ringback/OOS digital line tone generation may be incorrectly inserted into the wrong mixer-group (F0026633).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode. (F0014674)
Known Defects/Issues in Version 2.000.1.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration. (F0014383)
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface). (F0014414)
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation. (F0018368)
- New Spansion NAND flash incorrectly reported. (F0026510)
- Specific network disruption failover modes can leave remote iG330 indicating WAN errors until there is a signalling event. (F0026671)
New Features Added in Version 1.200.1.0
- Pass-through of in-band Ringback tone from T1/E1 channels to ARD SbRTP conferences.
- Generation of Unobtainable tone when the T1/E1 line interface is Out-of-Service.
- Country-specific Ringback and Unobtainable tone generation.
Defects Resolved in Version 1.200.1.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- Improvements to the calculation of the DSP capacity displayed on the Home web page (F0019224).
- The Voice Recording web page shows 30 channels in T1 mode, but only 24 actually exist (F0019544).
- The iG330 can occasionally reset when SSH is being enabled via the web interface. (F0018285)
Known Defects/Issues in Version 1.200.1.0
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
-
IP WAN links that are connected to a mixer group and then updated with an IP address of 0.0.0.0 are still
shown attached to the mixer group and cannot be deselected (F0015529).
-
Poor network conditions can occassionally cause IP WAN links to display the error No Rx RTCP and the links can remain faulty
until reset at the opposite side of the link (F0015692).
-
It is possible to have greyed out ticks against SbRTP links and T1/E1 channels for a mixer group
on the Voice Service web page that are not assigned to any group (F0017623).
- The .sh upgrader file has to be placed in the root directory of the TFTP server for the upgrade to be successful (F0017793).
- The iG330 can occassionally reset when SSH is being enabled via the web interface (F0018285).
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation (F0018368).
New Features Added in Version 1.112.3.0
- No new features added in this release
Defects Resolved in Version 1.112.3.0
-
The iG330 can generate SSRC values for SbRTP streams that the iD808 considers to be out of range
resulting in the iD808 discarding state changes (F0019061)
Known Defects/Issues in Version 1.112.3.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
-
IP WAN links that are connected to a mixer group and then updated with an IP address of 0.0.0.0 are still
shown attached to the mixer group and cannot be deselected (F0015529).
-
Poor network conditions can occassionally cause IP WAN links to display the error No Rx RTCP and the links can remain faulty
until reset at the opposite side of the link (F0015692).
-
It is possible to have greyed out ticks against SbRTP links and T1/E1 channels for a mixer group
on the Voice Service web page that are not assigned to any group (F0017623).
- The .sh upgrader file has to be placed in the root directory of the TFTP server for the upgrade to be successful (F0017793).
- The iG330 can occassionally reset when SSH is being enabled via the web interface (F0018285).
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation (F0018368).
New Features Added in Version 1.112.2.0
- Support added for Samsung K9F2G08U0C-SCB0 flash devices
- New default values for the E1/T1 Signal Customisation
Defects Resolved in Version 1.112.2.0
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458, F0018882).
- Restore doesn't work if the restore file is converted from Unix to Windows format (F0018881)
Known Defects/Issues in Version 1.112.2.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
-
IP WAN links that are connected to a mixer group and then updated with an IP address of 0.0.0.0 are still
shown attached to the mixer group and cannot be deselected (F0015529).
-
Poor network conditions can occassionally cause IP WAN links to display the error No Rx RTCP and the links can remain faulty
until reset at the opposite side of the link (F0015692).
-
It is possible to have greyed out ticks against SbRTP links and T1/E1 channels for a mixer group
on the Voice Service web page that are not assigned to any group (F0017623).
- The .sh upgrader file has to be placed in the root directory of the TFTP server for the upgrade to be successful (F0017793).
- The iG330 can occassionally reset when SSH is being enabled via the web interface (F0018285).
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation (F0018368).
New Features Added in Version 1.112.1.0
- Improved acoustic performance when using VAD on transmit SbRTP.
- Enhancement to prevent the iG330 remaining in the "Engineering mode" during start-up following repeated resets or power cycles.
- Enhanced WAN monitor tool including the display of peak values.
- Easier WAN monitor tool access.
-
New default values for the SbRTP port number and packet size and for the maximum number of
gateways per mixer.
- 'Network Mastering Clock' configuration replaced by 'Network Clock Source' configuration on the 'Trunk Settings' web page.
- SbRTP VAD configuration changed to a per channel basis.
- Improvement to the in-band MRD ringback tone generation.
-
New default values for the E1/T1 Signal Customisation and these are automatically applied when the E1/T1
line type is changed.
- Inactivity timeout for web pages extended to 15 minutes.
Defects Resolved in Version 1.112.1.0
-
Even when the groups are not enabled (but have SbRTP or WAN links as their members) the DSP Limit warning is
displayed when selecting a new WAN link in the mixers group web page (F0016825)
- The readme file for the WAN monitor tool should indicate the procedure for copying shortcuts (F0018792)
Known Defects/Issues in Version 1.112.1.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
-
IP WAN links that are connected to a mixer group and then updated with an IP address of 0.0.0.0 are still
shown attached to the mixer group and cannot be deselected (F0015529).
-
Poor network conditions can occassionally cause IP WAN links to display the error No Rx RTCP and the links can remain faulty
until reset at the opposite side of the link (F0015692).
-
It is possible to have greyed out ticks against SbRTP links and T1/E1 channels for a mixer group
on the Voice Service web page that are not assigned to any group (F0017623).
- The .sh upgrader file has to be placed in the root directory of the TFTP server for the upgrade to be successful (F0017793).
- The iG330 can occassionally reset when SSH is being enabled via the web interface (F0018285).
- The DebugDsp utility can periodically report the error message "Command error code:82 message 0" during normal operation (F0018368).
Corrections to iG330v1.1 firmware for voice quality issues.
New Features Added in Version 1.111.2.0
Defects Resolved in Version 1.111.2.0
- Low-level audio clicks heard when using low bandwidth SbRTP and with VAD enabled (F0016649).
- Low-level audio tone heard instead of silence when using T1 link with signalling present (F0016675).
- Corrected u-law codec line level on T1/E1 interface (F0012985).
Known Defects/Issues in Version 1.111.2.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
Re-issue of 1.110.3.0 with corrected version number.
New Features Added in Version 1.111.1.0
Defects Resolved in Version 1.111.1.0
- Miscellaneous minor code tidy-ups to fix compilation warnings and remove potential bugs.
- Tidy up CM utility to improve error handling and help text.
- Replaced a GPL licensed file used by 'Discover' and 'AutoDiscovery responder' to remove open-source licensing terms from this code.
- Fix problem where SbRTP & WAN channel status web page reports unknown signalling for privacy and global muting signals (F0016223)
- Fix problem where DSCP value is incorrectly bit-shifted in RTP & SbRTP packets (F0016560).
- Fix problem where audio from the remote end is not heard at the call originator for a short time after an ARD call is answered (F0016589).
Known Defects/Issues in Version 1.111.1.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
Corrections to iG330v1.1 firmware for voice quality issues.
New Features Added in Version 1.110.3.0
Defects Resolved in Version 1.110.3.0
- Miscellaneous minor code tidy-ups to fix compilation warnings and remove potential bugs.
- Tidy up CM utility to improve error handling and help text.
- Replaced a GPL licensed file used by 'Discover' and 'AutoDiscovery responder' to remove open-source licensing terms from this code.
- Fix problem where SbRTP & WAN channel status web page reports unknown signalling for privacy and global muting signals (F0016223)
- Fix problem where DSCP value is incorrectly bit-shifted in RTP & SbRTP packets (F0016560).
- Fix problem where audio from the remote end is not heard at the call originator for a short time after an ARD call is answered (F0016589).
Known Defects/Issues in Version 1.110.3.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
Change to iG330v1.1 firmware as a result of customer requirements.
New Features Added in Version 1.110.2.0
- The expiry time for the self-signed certifcate used for HTTPS has been increased to 10 years and is now valid until Feb 27 2020 12:52:25 GMT.
Defects Resolved in Version 1.110.2.0
- Fix problem where a tftp transfer breaks if a DHCP lease renewal happens at the same time. (F0015407)
- Fix problem where DSP run out of jitter buffer memory when its utilization is more than 90%.
- Fix problem to update the information about the LAN statistics whenever ALERT_ACTIVE_LINK_SSRC_CONTROLBYTES alert is received.
- Fix problem for the LAN statistics page that was reported when there was huge chunk of statistics data.
Known Defects/Issues in Version 1.110.2.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
Change to iG330v1.1 firmware as a result of customer requirements.
New Features Added in Version 1.110.1.0
- Add new 'low bandwidth' SbRTP codec option of 8KHz Alaw with matching automatic Payload Type adjustment.
Defects Resolved in Version 1.110.1.0
- Fix problem where repeated attempts to login to the web interface from a 2nd browser stop the 1st login from timing out. (F0015270)
- Fix problem where stale DSP loading was reported on the home page when in Voice Recorder mode.
Known Defects/Issues in Version 1.110.1.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
- The web server certificate will expire on 31st January 2012.
Change to iG330v1.1 firmware following component change.
New Features Added in Version 1.100.6.0
- Add U-boot support for new NAND flash device (Micron MT29F2G08AADWP/D).
Defects Resolved in Version 1.100.6.0
- Web page spelling correction.
Known Defects/Issues in Version 1.100.6.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- WAN errors reported in normal gateway mode remain visible in Voice Recorder mode (F0014674).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
Bug fixes and enhancements to iG330v1.1 firmware following validation testing.
New Features Added in Version 1.100.5.0
- Add startup code to prevent the unit entering an endless 'reset loop' as a result of unit failures that initiate a reset.
Defects Resolved in Version 1.100.5.0
- DSP would hang, resulting in a unit reset, when more than 31 links were present in a group (F0014600).
- Handset was incorrectly set up after a reboot when attached to a mesh group (F0014651).
Known Defects/Issues in Version 1.100.5.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
Bug fixes and enhancements to iG330v1.1 firmware following validation testing.
New Features Added in Version 1.100.4.0
- Web page enhancements:-
- Hide loopback mask setting when not applicable to selected loopback mode.
- Clarification of 'mute rx' operation.
- Display configured DSP % loading.
- Hide non-active streams in LAN statistics web page.
Defects Resolved in Version 1.100.4.0
- SbRTP listen-only setting was not reapplied when the group was re-enabled (F0014298).
- Odd port numbers were allowed to be assigned to SbRTP, IP-WAN and Voice Recorder streams (F0014359).
- Stale information was displayed on the LAN statistics web page after the connection had cleared (F0014369).
- Default Voice Recording stream ports were not allocated sequentially (F0014379).
- Handset audio was not heard in mesh-mode groups (F0014409).
- Latched Hoot audio was not transmitted when the group was re-enabled (F0014426).
- Default value for IP-WAN TTL was set to 1 instead of 120 (F0014432).
- 'WAN monitor' launch file was not relocatable (F0014437).
- Unreachable destination could be reported for non-local IP address with certain gateway equipment (F0014538).
- Web interface correctly reported IE6 but then stated it is not supported (F0014570).
Known Defects/Issues in Version 1.100.4.0
- Audio from groups containing T1/E1 channels can be distorted or missing if the T1/E1 line is disconnected (F0014030).
- DSP can hang, resulting in a unit reset, when the unit undergoes significant reconfiguration (F0014383).
- The handset is not added to a mesh-mode group until the group is re-enabled (automatically done if via web interface) (F0014414).
- Handset audio is not transmitted on SbRTP links when there are no active talkers (F0014458).
- DSP can unexpectedly mute audio streams when an internal mixer with no outputs is defined (this scenario should not occur with this version of iG330 firmware) (F0014561).
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
Bug fixes and enhancements to iG330v1.1 firmware following validation testing.
New Features Added in Version 1.100.3.0
- Web pages optimised for resolutions of 1024x768 and upwards.
Defects Resolved in Version 1.100.3.0
- Fix problem where RTP Voice Recorder stream is rejected when the VR IP address is left as zero (F0014223).
- Fix problem where audio is not mixed if no SbRTP member is present in a group (F0014229).
Known Defects/Issues in Version 1.100.3.0
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
Bug fixes and enhancements to iG330v1.1 firmware following validation testing.
New Features Added in Version 1.100.2.0
- Default setting for SSH is now set to 'disabled'.
- Add web page support for controlling T1/E1 channel transmit gain in Voice Recorder mode.
- Change web page operation to clear an invalid SbRTP multicast IP address to 0.0.0.0.
Defects Resolved in Version 1.100.2.0
- Fix problem where web server can occasionally stop responding (F0014138).
- Fix problem where Mesh Mode using T1/E1 channels is not supported (F0014143).
- Fix problem where the IP WAN channel configuration web page sometimes does not get displayed (F0014166).
Known Defects/Issues in Version 1.100.2.0
-
The limitations of CAS signalling mean that a non-hoot mesh that consists of multiple T1/E1 channels will
not operate in the same manner as an IP WAN mesh.
This is the first release of iG330v1.1 and contains the following additional features over v1:
iG330 General
- Adds support for flexible configuration - up to 30 groups can be configured into gateway, hub, mesh and LAN-mixer modes.
- Adds support for 30 IP WAN streams that can be individually configured into mixer groups.
- Adds password protected secure web interface to allow the unit to be remotely configured.
- Adds diagnostic monitor tool and the ability to mute 'noisy' sources.
iG330 WAN interface
- Supports Hoot, MRD and ARD conferences.
- Supports configuration of per-link TTL, DSCP, packet size, codec and VAD.
- Supports dedicated secondary IP address for all WAN streams.
- Supports 'RTP only' mode for third party interworking.
iG330 SbRTP interface
- Adds control of per-link packet size.
- Adds per-link 'listen only' mode to prevent transmission of SbRTP.
iG330 T1/E1 interface
- Add support for per-channel independent Rx & Tx gain adjustment.
iG330 Voice Recorder interface
- Add support for G.729 and G.722 codecs.
This is the first release of iG330v1 and contains the following features:
iG330 General
- Provides a single T1 or E1 gateway for either SbRTP private-wire protocols or Voice Recorder streams.
- Supports upto 30 fixed associations of 1 SbRTP private-wire or Voice Recorder link to a single T1/E1 channel.
- Configuration via the RS232 port via the separate Windows Configuration Application.
- Supports DHCP or manual network configuration.
- Supports diagnostic handset attached to one conference.
- Supports 'offline' mode to allow a secondary unit to take over gateway functionality.
- Supports secure engineering access via SSH for diagnostic purposes.
iG330 Mechanicals
- Supports integral dual redundant hot-swappable 100-240V AC power supplies with individual LED status indicators.
- Provides indication of SbRTP traffic on the LAN Tx & Rx via 2 green LEDs.
- Provides indication of unit status via tri-colour 'ready' LED.
- Provides indication of T1/E1 interface status via a series of alarm LEDs.
- Provides 1 x T1/E1 Ports supporting Channel Associated Signalling (CAS) via RJ-48C for connection to a carrier network.
- Provides 1 x T1/E1 Ports supporting Channel Associated Signalling (CAS) via RJ-48C for connection to a secondary unit.
- Provides RS232 serial interface (38400bps, 8 data bits, 1 stop bit, no parity and software flow control).
-
Physically the unit has two Ethernet ports but for this release only one of these
ports (NET1) is utilised in normal operation. The other port (NET 2) is disabled.
- The unit has a single USB type A socket but for this release the port is not utilised in normal operation.
- The unit has a single WAN error LED, but as WAN functionality is not included in this release, this LED will always be off.
iG330 SbRTP interface
- Supports Hoot, MRD and ARD conferences.
- Supports configuration of TTL, DSCP, packet size, payload code and VAD (applied to all links).
iG330 Voice Recorder interface
- Supports dedicated secondary IP address for Voice Recorder streams.
- Supports per-link configuration of packet size and VAD.
- Supports per-link selection of G.711 A or μ law.
iG330 T1/E1 interface
- Supports CAS and Robbed bit signalling.
- Supports 24 or 30 channels for T1 and E1 respectively with support for unused timeslots.
- Supports both NT and TE modes with external or internal clock sources.
- Supports remote & local line loopbacks, remote payload loopback and remote per-channel payload loopback.
- Supports per-channel selection of G.711 A or μ law.
- Supports customisation of minimum CAS and SbRTP MRD ring duration.
- Supports selectable ring-indication tone insertion on all channels.
- T1 support of AMI and B8ZS line codes with D4 (SF) and ESF framing.
- T1 detection of LOS, LOF, RAI and AIS alarms.
- T1 support of Line Buildout settings to compensate for different cable characteristics.
- E1 support of HDB3 line code with G704 framing and optional CRC4.
- E1 detection of LOS, LOF, RAI and AIS alarms and CRC4 errors.
-
Supports the following CAS signalling variants:-
E&M (immediate, wink & delay), ground start, loop start, D3 PLAR, D4 PLAR, Ringdown, 3 x D4_PLAR custom modes, 3 x Ringdown custom modes and a 'no signalling' option.
Back
to the Home Page